Stamina 15-7100 Manuel d'utilisateur

Model#: 15-7100STAMINA PRODUCTSMADE IN CHINAProduct May Vary SlightlyFrom Pictured.Exercise can present a healthrisk. Consult a physicianbefore beginn

ASSEMBLY INSTRUCTIONS10STEP 7Refer to the inset drawing. Plug the PULSE COIL WIRE(42) into the SOCKET of the PULSE EXTENSIONWIRE(40) located on the RE

ASSEMBLY INSTRUCTIONS11STEP 9NOTE: The RIGHT PEDAL(38) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(38) hasright hand threads and is t

ASSEMBLY INSTRUCTIONS12STEP 11Refer to the inset drawing. Run the CONNECTION WIRE(25) through the hole in the plate on theHANDLEBAR(4). Attach the HAN

13SET UP INSTRUCTIONSPlace the Magnetic Fusion 7100 Bike in the area where it will be used. It is recommended that the MagneticFusion 7100 Bike be pla

OPERATIONAL INSTRUCTIONSSEAT ADJUSTMENTLOAD ADJUSTMENTCAUTION:1.2.Rotate the ADJUSTMENT KNOB(51) counterclockwise until the pin releases when the knob

COMPUTER INSTRUCTIONS15MAIN DISPLAY PANELLCD MONITOR:1.2.This computer provides different programsdesigned to help you meet your fitnessgoals. Simply

16COMPUTER INSTRUCTIONSPROGRAM DESCRIPTIONS(P0) MANUAL(P1) FAT BURN (P2) MAX. FAT BURN (P3) AEROBIC(P4) HILL (P5) MOUNTAIN(P6) PLATEAUMANUAL PR

COMPUTER INSTRUCTIONSCOMPUTER OPERATION17STEP 1: POWER ONPedaling or press the MODE button.STEP 2: SET THE PROGRAMStop pedaling for four seconds. Pr

181.2.3.4.To store the Magnetic Fusion 7100 Bike, simply keep it in a clean dry place.Adjust the SEAT FRAME(7) to the lowest position. The Magnetic Fu

CONDITIONING GUIDELINESHow you begin your exercise program depends on your physical condition. If you have been inactive forseveral years or are sever

TABLE OF CONTENTSSafety Instructions 2Before You Begin 4Equipment Warning & Notice Labels 5Hardware Identification Chart 6Assembly Instruc

WARM-UP and COOL-DOWNWarm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries.Warm up for two to five minute

WARRANTYLIMITED WARRANTYMODEL 15-7100Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanshipunder nor

PRODUCT PARTS DRAWING22FRONTBACK

PARTS LIST PART# PART NAME QTY 1 Front Frame 1 2 Front Stabilizer 1 3 Upright 1 4 Handlebar 1 5 Rear Frame 1 6 Rear Stabilizer

51 Adjustment Knob 152 Stopper 453 Foam Grip 254 Wheel 155 Foot Cap 256 Foot Stand 257 Leveling Cap 258 Cap Bushing 25

25NOTES

IMPORTANT : Before filling out the form below make sure you have the right information.Refer to the parts list to make sure you're ordering the

THANK YOU FOR PURCHASING THEMagnetic Fusion 7100 BikeTo help you get started, we have pre-assembled most of yourMagnetic Fusion 7100 Bike at the facto

BEFORE YOU BEGIN4SeatRear StabilizerFoot CapRight CrankRight CoverBack CushionLeveling CapSeat FrameRight PedalLeft PedalUpright SleeveFront FrameComp

EQUIPMENT WARNING & NOTICE LABELSThis chart is provided to help identify the warning & notice labels on the Magnetic Fusion 7100 Bike.Please t

HARDWARE IDENTIFICATION CHARTThis chart is provided to help identify the hardware used in the assembly process. Place the washers or theends of the bo

ASSEMBLY INSTRUCTIONS7STEP 1Make the WHEEL(54) on the FRONT STABILIZER(2) face the front, then attach the FRONT STABILIZER(2)to the FRONT FRAME(1) wit

ASSEMBLY INSTRUCTIONS8STEP 3Attach the REAR STABILIZER(6) to the REAR FRAME(5) with CARRIAGE BOLTS(M8x1.25x75mm)(63),ARC WASHERS(M8)(86), LOCK WASHERS

ASSEMBLY INSTRUCTIONS9A.B.(Assembledat the factory)STEP 5Refer to illustration A. Attach the HANDRAIL(8) to the SEAT FRAME(7) with CARRIAGE BOLTS(M8x1